Yeoman and servicing Manuel d'instructions

YEOMAN CL3 & CL5Instructions for Use,Installation and ServicingFor use in GB, IE (Great Britain and Eire)PR1406 Issue 1 (October 2011)IMPORTANTTHE

108. FLAME FAILURE DEVICE8.1 This is a safety feature incorporated on this appliance which automatically switches off the gas supply if the pilot goe

11INSTALLATION INSTRUCTIONSTECHNICAL SPECIFICATIONCOVERING THE FOLLOWING MODELS:Model Gas CAT.Gas Type WorkingPressureAeration Injector Gas Ratem3/hIn

12INSTALLATION INSTRUCTIONSTECHNICAL SPECIFICATIONThis appliance has been certified for use in countries other than those stated. To install this appl

13INSTALLATION INSTRUCTIONSSITE REQUIREMENTS Note: This appliance must only be installed with the flue supplied.You must adhere to the following: 1.1

142. REAR FLUE2.1 REAR FLUE KITYEOMAN CL BF (8526)AR0630a2200mm min550mm max Terminal dimensions: 395 x 200 x 200 mm (H x W x D) Guard supplied C

15INSTALLATION INSTRUCTIONSSITE REQUIREMENTS3C. TOP FLUE UP AND OUT WITH ADDITIONAL BEND3.11 An additional bend can be used on the horizontal sectio

16INSTALLATION INSTRUCTIONSSITE REQUIREMENTS5. GAS SUPPLY THIS APPLIANCE IS INTENDED FOR USE ON A GAS INSTALLATION WITH A GOVERNED METER.5.1 Before

17 The specified clearances provide the minimum distance to combustible materials. If the appliance is intended to be installed into a non-combustibl

18INSTALLATION INSTRUCTIONSINSTALLATION1AR26942.3 Remove the frame to gain complete access to the control box and the viewing aperture by lifting the

19INSTALLATION INSTRUCTIONSINSTALLATION NOTE: For Top Exit appliances the flue collar must be placed on the flue exit before the top is fitted.3.2 T

2COVERING THE FOLLOWING MODEL: PAGEAPPLIANCE COMMISSIONING CHECKLIST 3USER INSTRUCTIONS 4 INSTALLATION INSTRUCTIONS 14 Technical Specifications

20INSTALLATION INSTRUCTIONSINSTALLATIONFlue and Appliance Fixings4.13 Position the appliance observing appropriate clearances.4.14 Apply a bead of s

21INSTALLATION INSTRUCTIONSINSTALLATION4B TOP EXIT - UP & OUT ENSURE THE BLACK DECORATIVE TOP AND COLLAR ARE FITTED TO THE TOP OF THE APPLIANCE

22INSTALLATION INSTRUCTIONSINSTALLATIONFlue and Appliance Fixings4.34 Pull appliance and flue assembly away from the hearth.4.35 Drill four fixing h

23INSTALLATION INSTRUCTIONSINSTALLATION6. LOG LAYOUT LOGS MUST BE POSITIONED ACCORDING TO THE FOLLOWING INSTRUCTIONS TO GIVE THE CORRECT FLAME EFFECT

24INSTALLATION INSTRUCTIONSINSTALLATION17AR2103Log 26a.4 Place the third log into the groove on the right hand side and ensure it is pushed as far in

25INSTALLATION INSTRUCTIONSINSTALLATION22AR2103Log 16b.3 Place the second log into the left hand groove on the burner tray, Diagram 23. The log shou

267. COMPLETION OF ASSEMBLY7.1 To fit the window frame: Offer the frame to the foot of the opening and secure using 8 screws as shown, Diagram 28.2

278.1 To light the appliance using the remote handset press the On/Off button (�) followed directly by the OK button. The appliance will emit a beep

288.17 From the medium setting press the UP (w) button once to increase the flame setting to high. YELLOW FLAMES WILL APPEAR WHEN THE FIRE HAS GAINE

291. COMMISSIONING THE APPLIANCE1.1 Complete the Commissioning Checklist at the front of this manual covering: — Flue checks — Gas checks — Log la

3FLUE CHECK PASS FAIL1. Flue is correct for appliance 2. Flue flow test N/A 3. Spillage test N/A GAS CHECK 1. Gas soundness & let by test2.

30 If there are any difficulties achieving pairing ensure that the handset is set to Channel A. To do this follow the steps below:2.8 Press the On/O

31SERVICING INSTRUCTIONSSERVICING/FAULTFINDINGCHARTS1. SERVICING REQUIREMENTSIMPORTANT – The glass panel on this appliance should be checked for a

32SERVICING INSTRUCTIONSFAULT FINDING CHARTSPILOT WILL NOT STAY LIT OR FIRE GOES OUT IN USEEnsure there is no debris around the pilot assembly, (e.g.

33SERVICING INSTRUCTIONSFAULT FINDING CHARTSELECTRONIC CONTROL VALVE FAULT ANALYSIS Problem Cause Error Message LCD Display SolutionDoes not igniteNo

2AR26932.2 Remove the frame to gain complete access to the control box and the viewing aperture by lifting the hooks clear of the slots on the front

35SERVICING INSTRUCTIONSREPLACING PARTS 4. BAFFLE & CERAMIC LINERS4.1 To access the burner tray and interior workings of the appliance it may be

3618AR21504.8 To replace the liners liner and baffle reverse these procedures.5. MAIN BURNER5.1 To remove the main burner: Remove the baffle and ce

37SERVICING INSTRUCTIONSREPLACING PARTS22AR16047.5 To remove the electrode, disconnect the ignition lead and undo the retaining nut. The electrode c

38SERVICING INSTRUCTIONSREPLACING PARTS To change the gas valve:9.1 Disconnect the pilot pipe. 9.2 Disconnect the thermocouple, interrupter leads a

39SERVICING INSTRUCTIONSREPLACING PARTS11.4 After replacing the control box ensure all cables and connections are refitted as detailed in Diagram 28.

4USER INSTRUCTIONS 1. GENERAL In the event of a gas escape or if you can smell gas, please take the following steps: • Immediatelyturnoffthegas

4013. PRIMARY AERATION PLATE NOT ALL MODELS HAVE AERATION PLATES. REFER TO NOTE AT BEGINNING OF INSTALLATION INSTRUCTIONS.13.1 Remove the burner mod

41SERVICING INSTRUCTIONSREPLACING PARTSCL3 CL5COMPONENT NG LPG NG LPGPILOT INJECTOR PI0026 PI0015 PI0026 PI0015MAIN INJECTOR IN0040 IN0071 IN0060 IN0

42

43SERVICE RECORDS1ST SERVICEDate of Service:...Next Service Due:...

Yeoman Limited, Osprey Road, Sowton Industrial Estate, Exeter, Devon, England EX2 7JGTel: (01392) 261999 Fax: (01392) 444148 E-mail: [email protected]

5USER INSTRUCTIONS2.1 To light the appliance using the remote handset press the On/Off (�) button followed directly by the OK button. The appliance w

6USER INSTRUCTIONS2.16 From the low setting press the UP (w) button once to increase the flame setting to medium.2.17 From the medium setting press

7USER INSTRUCTIONS5. CHANGING THE YEOMAN CL BATTERIES5.1 The appliance batteries are located to the left hand side of the touch pad. This is behind t

8USER INSTRUCTIONS7a.3 Place the second log into the left hand groove on the burner tray and ensure it is pushed as far into the centre as the groove

9USER INSTRUCTIONS15AR2103Log 17b.3 Place the second log into the left hand groove on the burner tray, Diagram 16. The log should butt up against th